Wildlife camera/trail camera 500 SD V2

Name: Wildlife camera/trail camera 500 SD V2
Availability: InStock

With this camera, you can take photos (48MP) or videos (4K ULTRA HD) of the wildlife in your area, day or night. 16 GB SD card included. Detection range: 25 m. LCD display

ID 8997047

Sold and shipped by

How to get it

image quality
Photos up to 48 MP and 4K ULTRA HD videos.
fast acting
Trigger speed of less than 1 seconds.
distance
Motion detection at up to 25 m (depending on conditions) and flash lighting.
field of vision
Detection angle: 120°.
capacity
16 GB SD card (included).
ease of use
Easy to use, with its 3 capture modes (photo/video/photo+video).
visual efficiency
Built-in LCD screen for configuration and field previews.

Details

Design details

Technical characteristics
Screen: LCDTrigger time: 0.8 seconds Detection angle: 120° Motion detection up to 25 m Operation: day/night Image resolution: 48 MP Video resolution: 4K ULTRA HD Waterproofing: IPX4 Weight: 340 g Dimensions: 118 x 145 x 75 mm
Pack contents
- 1 camera - 1 16 GB SD card - 1 USB cable - 1 mounting strap - 1 user guide Note: the 8 AA LR6 batteries are not included.
Setup and power supply
The product comes with a 16GB SD memory card already installed. If you decide to use another card, ensure it is Class U3 or faster before inserting it into the slot. For installation: - open the battery compartment by releasing the latches, then pressing the battery compartment release button - insert 8 x 1.5 V AA LR6 batteries (alkaline or, preferably, lithium for longer battery life and better performance in cold weather) - close the compartment
Safety information
This camera is compatible with a 6V adaptor and 4 AA batteries (adaptor and batteries not included). Caution! If you connect the camera trap to a power supply above 10 V, you may damage the product (see instructions).
Quick configuration and operating modes (part 1/3)
Quick configuration: To configure the device, move the switch to “SETUP”. Capture mode: -photo: takes photos -video: records video clips -photo + video: takes a photo followed by a video Detection delay: This is the interval between 2 consecutive photo or video captures. Note that a short detection delay will result in more captures and increase battery consumption.
Quick configuration and operating modes (part 2/3)
Motion detector sensitivity: -high, for open areas and small animals-medium, to minimise unwanted shots caused by wind or moving leaves Getting started: Once the settings are configured, move the switch to “ON”. The device will delay for a few seconds to give you time to move away. Note that you can set an operating schedule for the camera, via the “Operating schedule” menu.
Quick configuration and operating modes (part 3/3)
Start-up (continued): This will allow you, for example, to operate the camera only at night or during specific periods; this mode will preserve battery life. In the drop-down menu, you can further customise the settings to suit your needs (burst mode, video duration, photo resolution, etc.).
Positioning (part 1 of 3)
Proper positioning is crucial for obtaining high-quality photos. The camera trap operates using a heat sensor (PIR). When choosing a location, opt for obvious spots: look for established paths or runs (small trails regularly used by animals), watering holes (water sources), or signs of activity (rubs and scrapes on trees). Also focus on areas of interest: feeding station, active burrow or obstacle to the animals’ movement.
Positioning (part 2 of 3)
Angle: Perpendicular to the path, ideally positioning the camera so that the animal crosses the field of view horizontally rather than walking directly towards or away from the lens. This increases the time spent within the detection zone. Height: Set the trap at a height of 0.5 to 1 m from the ground. For large game (deer, for example), aim higher. For small animals (rabbits, foxes), aim lower.
Positioning (part 3 of 3)
Distance: The optimal capture distance is typically between 5 and 10 m in front of the device. Avoiding false triggers: Avoid pointing the camera directly east or west, especially in summer. The heat from the rising or setting sun can cause false triggers or overexposed photos. Clear away any branches, tall grass or leaves that could move in front of the PIR sensor. The movement of plants and trees swaying in the wind is the main cause of ‘empty’ photos.
Maintenance
Check the camera trap regularly (preferably every 3 to 7 days) to retrieve the images and check the condition of the batteries. Clean the lens and PIR sensor with a soft cloth as needed. If not used for an extended period, remove the batteries to prevent leakage and damage to the camera.

Wildlife camera/trail camera 500 SD V2

How to get it

Features

image quality

fast acting

distance

field of vision

capacity

ease of use

visual efficiency

Details

Design details

Specifications

Details

Composition

Manufacturer

Usage & care

Details

Design details

Specifications

Details

Composition

Manufacturer

Specifications

Details

Composition

Manufacturer

Usage & care

How to use

Everything you need to know

How to repair or replace

2-year warranty

Care instructions

Specifications

Details

Composition

Manufacturer

How to use

Everything you need to know

How to repair or replace

2-year warranty

Care instructions